Call 08048600090 88% Response Rate

Send Email

Tube Fittings

Our product range includes a wide range of stainless steel instrumentation tube fittings, uns s31803 duplex steel instrumentation fittings, nickel alloy instrumentation tube fittings, inconel instrumentation tube fittings, monel instrumentation tube fitting and hastelloy instrumentation tube fittings.
Stainless Steel Instrumentation Tube Fittings

Stainless Steel Instrumentation Tube Fittings

Product Price: Rs 190 / PCSGet Best Price

Product Details:
Usage/ApplicationChemical Plants
Material GradeSS304
BrandMPJ
MaterialStainless Steel
Minimum Outer Diameter6.00 mm
Maximum Outer Diameter25.4 mm
Melting Point1350 Degree C
Density8.44 g/cm3

M P Jain Tubing Solution is one of the leading Manufacturers, Supplier and Exporters of high quality Stainless Steel Instrumentation Tube Fittings in Mumbai, India. In addition to we make use of highly advance technology and machinery to carry out accurate and surface finishing product. We offer these instrumentation tubes in a wide range of standards, specifications, designations, and grade and custom dimensions. We also provide these tubes in altered dimensions for the complex type of tube fittings. The SS instrumentation tube fittings work reliably on both welded and seamless drawn products. These are fully annealed type. These are manufactured using high quality raw material and advanced technology to meet the diverse requirements of our customers. We are manufactured as per the national & international quality standards.

 

The alloys used in Stainless Steel Instrumentation Tube Fittings are stainless steel 18-8 chromium and nickel. We use Carbon content of up to 0.4 to 0.10%. Which provide it high strength and temperature exceeding 430 degrees C.? These pipe fitting are corrosive resistance and used in a wide range of application. It also provides good oxidizing resistance quality. You can use this technique in different applications. These pipe fitting can be used in a wide range of temperatures. As these pipe fittings have a great strength they provide a long life service.

Available Grades:

  • SS304, SS304L, SS304H, SS316, SS316L, SS316H, SS316Ti, SS310/310S, SS317/317L



Additional Information:

  • Packaging Details: Stainless Steel Instrumentation tube fittings are surface wash and clean to remove all impurities and stock in the warehouse. Then it is wrapped in thin plastic and also it ends are protected by plastic caps to avoid any damage in transit. Stainless Steel Instrumentation tube fittings is bundled in bubble wrap followed by assorting them in colored plastic bundles. An outer rope is tied to protect the tubing and they are packed in wooden box or container. M P Jain Provide Stainless Steel Instrumentation tube fittings with all necessary documents such as commercial invoice, packing list, Test Reports, HS Code, Country of Origin attested by the chamber of commerce, Fumigation Certificate, Warranty Letter, and Base Material Certificates. Every lot is supplied with a material test certificate as per EN 10204 NACE 3.1 standards indicating the chemical and mechanical properties of the Instrumentation Tubes. We also confirm the guarantee of the Stainless Steel Instrumentation tube fittings supplied as per Purchase order specifications and attest the same in the Material Test Certificate. We also welcome any third party inspection from an agency nominated by the customer to comply with NACE 3.2 Certification if required by the customer at an extra cost.
Get Best QuoteRequest A Callback
UNS S31803 Duplex Steel Instrumentation Fittings

UNS S31803 Duplex Steel Instrumentation Fittings

Product Price: Rs 180 / PieceGet Best Price

Product Details:
Usage/ApplicationPharmaceuticals Industrial
Material GradeDuplex Steel UNS S31803
MaterialDuplex Steel
BrandMPJ
Country of OriginMade in India
Minimum Outer Diameter2 mm
Maximum Outer Diameter50 mm

M P Jain Tubing Solutions is the traders and suppliers of UNS S31803 Duplex steel Instrumentation Fittings to a huge customer base globally. We deliver a broad range of custom made products to our customers across the globe. Duplex Steels instrumentation Fittings is highly ductile and offer better toughness than other grades of steels. These WNR 1.4462 Instrumentation fittings can provide resistance to corrosion similar to that of any austenitic steels. 

 

Duplex Stainless Steel Instrumentation Tube Fittings, Duplex Steel S31803 Instrumentation Fittings Suppliers, Duplex Steel UNS S31803 / S32205 Compression Tube Fittings, Duplex Steel S32205 Instrumentation Tube Fittings, DIN 1.4462 Instrumentation Tube Fittings, Grade S31803 / S32205 Duplex Steel Single Ferrule Fittings, SAF 2205 Instrumentation Fittings, Duplex Steel S31803 / S32205 Double Ferrule Tube Fittings


Specifications:

Duplex Steel UNS S31803 Instrumentation Fittings Specification

Specifications

ASTM A789 / ASME SA789

Size Range

1/16” OD to 2”OD, 2mm OD to 50mm OD.

Dimensions

DIN, ASTM, BS and all International Standards.

Thread

NPT Fittings, BSP Fittings, BSPT Fitting, UNF.

Pressure Rating

6000PSI for Stainless Steel, 300/1000/3000PSI for Brass.

 

Chemical properties:

Grade

   C

 Mn

   Si

    P

    S

   Cr

  Mo

  Ni

   N

   Fe

S31803

0.030 max

2.00 max

1.00 max

0.030 max

0.020 max

22.0 – 23.0

3.0 – 3.5

4.50 – 6.50

0.14 – 0.20

63.72 min

S32205

0.030 max

2.00 max

1.00 max

0.030 max

0.020 max

21.0 – 23.0

2.50 - 3.50

4.50 – 6.50

0.8 – 0.20

63.54 min



Additional Information:

  • Packaging Details: Duplex Instrumentation tube fittings are surface wash and clean to remove all impurities and stock in the warehouse. Then it is wrapped in thin plastic and also it ends are protected by plastic caps to avoid any damage in transit. Duplex Instrumentation tube fittings is bundled in bubble wrap followed by assorting them in colored plastic bundles. An outer rope is tied to protect the tubing and they are packed in wooden box or container. M P Jain Provide Duplex Instrumentation tube fittings with all necessary documents such as commercial invoice, packing list, Test Reports, HS Code, Country of Origin attested by the chamber of commerce, Fumigation Certificate, Warranty Letter, and Base Material Certificates. Every lot is supplied with a material test certificate as per EN 10204 NACE 3.1 standards indicating the chemical and mechanical properties of the Instrumentation Tubes. We also confirm the guarantee of the Duplex Instrumentation tube fittings supplied as per Purchase order specifications and attest the same in the Material Test Certificate. We also welcome any third party inspection from an agency nominated by the customer to comply with NACE 3.2 Certification if required by the customer at an extra cost.
Get Best QuoteRequest A Callback
Nickel Alloy Instrumentation Tube Fittings

Nickel Alloy Instrumentation Tube Fittings

Product Price: Rs 175 / PieceGet Best Price

Product Details:
Size1/16"
Usage/ApplicationPharmaceuticals Industrial
ShapeRound
BrandMPJ
MaterialNickel Alloy
Thickness6.00 mm
Melting Point1446 Degree C
Density8.9 g/cm3

As an acclaimed enterprise of the industry, M P Jain Tubing Solutions is involved in offering a vast array of Nickel Alloy Instrumentation Tube Fittings as a manufacturer, exporter, stockiest and supplier to our domestic and global clients. Nickel 200 Tube Fittings (UNS N02200) has good solderability and weldability. Nickel 200 Tube Fittings provides high thermal and electrical conductivity in comparison to nickel-base alloys, stainless and low alloy steels. Alloy 201 Tube Fittings (UNS N02201) is often used in chemical processing, food processing, synthetic fibre processing and more.

 

Nickel Alloy 201 Compression Tube Fittings, Alloy 201 Single Ferrule Tube Fittings, ASTM B160 201 Nickel Instrumentation Tube Fittings, Alloy 2.4068 Instrumentation Tube Fittings, Nickel Alloy UNS N02201 Instrumentation Tube Fittings, High Nickel Alloy 201 Instrumentation Tube Fittings, Nickel 201 Double Ferrule Tube Fittings Suppliers in Mumbai, India.

 

Nickel Alloy 200 / 201 Tube Fittings Chemical Composition:

         Grade

C

Ni

Mg

Cu

Fe

Ti

Mn

Si

S

Nickel Alloy 200

0.15 max

99.0 min

-

0.25 max

0.4 max

-

0.35 max

0.1 max

0.01 max

Nickel Alloy 201

0.02 max

99.0 min

0.15 max

0.25 max

0.4 max

0.1 max

0.35 max

0.2 max

0.01 max

 

Nickel Alloy 200 / 201 Tube Fittings Mechanical Properties:

Element

Density

Melting Point

Tensile Strength

Yield Strength (0.2%Offset)

Elongation

Nickel Alloy 200 / 201

8.9 g/cm3

1446 °C (2635 °F)

Psi – 67000 , MPa – 462

Psi – 21500 , MPa – 148

45 %

 

Nickel Alloy Instrumentation Tubing & Fittings Equivalent Grades:

Standard

Werkstoff Nr.

UNS

JIS

AFNOR

BS

GOST

EN

Nickel 200

2.4066

N02200

NW 2200

N-100M

NA 11

????-2

Ni 99.2

Nickel 201

2.4068

N02201

NW 2201

-

NA 12

????-2

LC-Ni 99


Specifications:
  • 0.6 mm to 6.00 mm
  • 1/16" 1/2" & 1.5 mm to 38.1 mm 



Additional Information:

  • Packaging Details: Nickel Alloy tube fittings are surface wash and clean to remove all impurities and stock in the warehouse. Then it is wrapped in thin plastic and also it ends are protected by plastic caps to avoid any damage in transit. Nickel Alloy Instrumentation tube fittings is bundled in bubble wrap followed by assorting them in colored plastic bundles. An outer rope is tied to protect the tubing and they are packed in wooden box or container. M P Jain Provide Nickel Alloy Instrumentation tube fittings with all necessary documents such as commercial invoice, packing list, Test Reports, HS Code, Country of Origin attested by the chamber of commerce, Fumigation Certificate, Warranty Letter, and Base Material Certificates. Every lot is supplied with a material test certificate as per EN 10204 NACE 3.1 standards indicating the chemical and mechanical properties of the Instrumentation Tubes. We also confirm the guarantee of the Nickel Alloy Instrumentation tube fittings supplied as per Purchase order specifications and attest the same in the Material Test Certificate. We also welcome any third party inspection from an agency nominated by the customer to comply with NACE 3.2 Certification if required by the customer at an extra cost.
Get Best QuoteRequest A Callback
Inconel Instrumentation Tube Fittings

Inconel Instrumentation Tube Fittings

Product Price: Rs 150 / PieceGet Best Price

Product Details:
Usage/ApplicationPharmaceuticals Industrial
Material GradeInconel 600
BrandMPJ
MaterialInconel
Country of OriginMade in India
Thickness3.6 mm
Outer Diameter50mm

M P Jain Tubing Solutions is a pioneer Stockist, manufacturer, supplier, and exporter of Inconel Instrumentation Tube Fittings which is available in all sizes, dimensions and prices. It is being used in the vast majority of today’s analytical and process instrumentation applications. Inconel 600 is an Alloy of Nickel and Chromium. We are the leading company to offer Inconel 600 instrumentation tube fittings which is having good flexibility and strength and it has amazing high chemical resistance and mechanical characteristics. All Inconel Instrumentation tube fitting is made with the ASTM standards.

 

Inconel 600 Nut, Inconel 600 Plug, Inconel Alloy 600 Bulkhead Male Connector, Inconel 600 Male Branch Tee, Buy Grade 600 Inconel ASTM B366 Female Elbow, Inconel 600 Male Connector, DIN 2.4816 Reducer Dealers, 600 Inconel Back Ferrule‎, Alloy UNS N06600 Male Adapter‎, Nickel Alloy 600 Female Tube Adapter Manufacturer in India, Inconel Alloy 600 Front Ferrule‎, Inconel 600 Bulkhead Union supplier, 600 Inconel Reducing Union.

 

Inconel 600 Tube Fittings Equivalent Grades:

STANDARD

UNS

WNR NO.

JIS

BS

GOST

AFNOR

EN

Inconel 600

N06600

2.4816

NCF 600

NA 13

?????????? 28-2,5-1,5

NC15FE11M

NiCr15Fe

 

Inconel 600 Tube Fittings Chemical Composition:

Grade

C

Mn

Si

S

Cu

Fe

Ni

Cr

Inconel 600

0.15 max

1.00 max

0.50 max

0.015max

0.50 max

6.00 – 10.00

72.00 min

14.00 – 17.00

 

Inconel 600 Tube Fittings Mechanical Properties: 

Grade

Density

Melting Point

Tensile Strength

Yield Strength (0.2%Offset)

Elongation

Inconel 600 

8.47 g/cm3

1413 °C (2580 °F)

Psi – 95,000 , MPa – 655

Psi – 45,000 , MPa – 310

40 %


Specifications:
  • 1/16"OD to 2"OD, 2mm OD to 50mm OD
  • Inconel 600 / 601 / 625 / 718 Inconel 800 / 800H / 800HT / 825
  • Tube To Union, Tube To Male, Tube To Female, Instrument Pipe Fittings, Accessories


Additional Information:

  • Packaging Details: Inconel Instrumentation tube fittings are surface wash and clean to remove all impurities and stock in the warehouse. Then it is wrapped in thin plastic and also it ends are protected by plastic caps to avoid any damage in transit. Inconel Instrumentation tube fittings is bundled in bubble wrap followed by assorting them in colored plastic bundles. An outer rope is tied to protect the tubing and they are packed in wooden box or container. M P Jain Provide inconel Instrumentation tube fittings with all necessary documents such as commercial invoice, packing list, Test Reports, HS Code, Country of Origin attested by the chamber of commerce, Fumigation Certificate, Warranty Letter, and Base Material Certificates. Every lot is supplied with a material test certificate as per EN 10204 NACE 3.1 standards indicating the chemical and mechanical properties of the Instrumentation Tubes. We also confirm the guarantee of the Inconel Instrumentation tube fittings supplied as per Purchase order specifications and attest the same in the Material Test Certificate. We also welcome any third party inspection from an agency nominated by the customer to comply with NACE 3.2 Certification if required by the customer at an extra cost.
Get Best QuoteRequest A Callback
Monel Instrumentation Tube Fitting

Monel Instrumentation Tube Fitting

Product Price: Rs 100 / PieceGet Best Price

Product Details:
Size38.1 mm
Usage/ApplicationPharmaceuticals Industrial, Textile Machineries
Material GradeMonel K500
BrandMPJ
MaterialMonel
Density8.44 g/cm3
Melting Point1350 Degree C

M P Jain Tubing Solutions Monel Instrumentation Tube Fittings are popularly known for its high tensile strength & corrosion resistance properties. The characteristics of the monel instrumentation tube fittings is that it is having very high ductility that is making it possible to form in flexible monel tubes as per the customer’s needs. We offer to our customers various types of shapes and sizes of monel tube fittings and also in different dimensions. Our product resists to vibration fatigue at high pressure or high temperature.


Monel Instrumentation Tubes Fittings Equivalent Grades:

STANDARD

WERKSTOFF NR.

UNS

AFNOR

JIS

GOST

BS

EN

Monel 400

2.4360

N04400

NU-30M

NW 4400

?????????? 28-2,5-1,5

NA 13

NiCu30Fe

Monel K500

2.4375

N05500

-

-

-

-

-


Monel Instrumentation Tubes Fittings Chemical Composition:

Grade

Ni

Fe

C

Mn

Si

Cu

Al

S

Monel 400

63.0 min

1.0 - 2.5

0.3 max

2.0 max

0.5 max

28.0 - 34.0

0.50 max

0.02 max

Monel K500

63.0 min

05 - 2

0.25 max

1.5 max

0.5 max

27.0 - 33.0

2.3 - 3.15

0.010 max


Monel Instrumentation Tubes Fittings Mechanical Properties:

Grade

Density

Melting Point

Tensile Strength Psi, Mpa

Yield Strength (0.2%Offset)

Elongation

Monel 400

8.8 g/cm3

1350 °C (2460 °F)

80,000, 550

240 Mpa

40 %

Monel K500

8.44 g/cm3

1350 °C (2460 °F)

1,60,000, 1100

790 Mpa

20 %



Additional Information:

  • Packaging Details: Monel Instrumentation tube fittings are surface wash and clean to remove all impurities and stock in the warehouse. Then it is wrapped in thin plastic and also it ends are protected by plastic caps to avoid any damage in transit. Monel Instrumentation tube fittings is bundled in bubble wrap followed by assorting them in colored plastic bundles. An outer rope is tied to protect the tubing and they are packed in wooden box or container. M P Jain Provide Monel Instrumentation tube fittings with all necessary documents such as commercial invoice, packing list, Test Reports, HS Code, Country of Origin attested by the chamber of commerce, Fumigation Certificate, Warranty Letter, and Base Material Certificates. Every lot is supplied with a material test certificate as per EN 10204 NACE 3.1 standards indicating the chemical and mechanical properties of the Instrumentation Tubes. We also confirm the guarantee of the Monel Instrumentation tube fittings supplied as per Purchase order specifications and attest the same in the Material Test Certificate. We also welcome any third party inspection from an agency nominated by the customer to comply with NACE 3.2 Certification if required by the customer at an extra cost.
Get Best QuoteRequest A Callback
Hastelloy Instrumentation Tube Fittings

Hastelloy Instrumentation Tube Fittings

Product Price: Rs 200 / PCSGet Best Price

Product Details:
Usage/ApplicationPharmaceuticals Industrial
MaterialHastelloy
BrandMPJ
ScheduleSch 10
Material GradeHastelloy C276
Surface TreatmentPolished
Country of OriginMade in India
Outer Diameter50 mm

M P Jain tubing Solutions is a supplier, manufacturer, exporter of a huge variety of products. We are an esteemed company that is pretty much engaged in giving a widespread variety of Hastelloy Instrumentation Tube Fittings. Hastelloy Instrumentation Tube Fittings are well known for their excellent corrosion resistance over a wide range of media. These Hastelloy Instrumentation Tubing Fittings have higher quality molybdenum content which impacts resistance to localized corrosion like pitting. Hastelloy Ferrule Tubes Fittings are a low carbon Inconel alloy that minimizes the carbide precipitation during welding.

 

Hastelloy Instrumentation Tube Fittings, Hastelloy Alloy C22 Ferrule Fittings, Worldwide Suppliers of DIN 2.4602 Hastelloy Compression Tube Fitting, ASME SB366 Hastelloy C-22 Double Ferrule Fittings, Premium Source Quality of ASTM B366 Hastelloy C22 High Pressure Tube Fittings, Largest Stockholders of Nickel Alloy UNS N06022 Single Ferrule Fittings, Low-cost Range of Hastelloy C22 Tube Fittings in Mumbai India.

 

Hastelloy C276 Tube Fittings Equivalent Grades:

STANDARD

UNS

WNR.

EN

JIS

OR

GOST

Hastelloy C276

N10276

2.4819

NiMo16Cr15W

NW 0276

????760

????65??????

 

Hastelloy C276 Tube Fittings Chemical Composition:

Grade

Ni

C

Mo

Mn

Si

Fe

P

S

Co

Cr

W

V

Hastelloy C276

Balance

0.01 max

15–17

1.0 max

0.08 max

4–7

0.04 max

0.03 max

2.5 max

14.5–16.5

3–4.5

0.35 max

 

Hastelloy C276 Tube Fittings Mechanical Properties:

Grade

Density

Melting Point

Tensile Strength

Yield Strength (0.2%Offset)

Elongation

Hastelloy C276

8.89 g/cm3

1370 °C (2500 °F)

Psi – 1,15,000 , MPa – 790

Psi – 52,000 , MPa – 355

40 %




Additional Information:

  • Packaging Details: Hastelloy Instrumentation tube fittings are surface wash and clean to remove all impurities and stock in the warehouse. Then it is wrapped in thin plastic and also it ends are protected by plastic caps to avoid any damage in transit. Hastelloy Instrumentation tube fittings is bundled in bubble wrap followed by assorting them in colored plastic bundles. An outer rope is tied to protect the tubing and they are packed in wooden box or container. M P Jain Provide Hastelloy Instrumentation tube fittings with all necessary documents such as commercial invoice, packing list, Test Reports, HS Code, Country of Origin attested by the chamber of commerce, Fumigation Certificate, Warranty Letter, and Base Material Certificates. Every lot is supplied with a material test certificate as per EN 10204 NACE 3.1 standards indicating the chemical and mechanical properties of the Instrumentation Tubes. We also confirm the guarantee of the Hastelloy Instrumentation tube fittings supplied as per Purchase order specifications and attest the same in the Material Test Certificate. We also welcome any third party inspection from an agency nominated by the customer to comply with NACE 3.2 Certification if required by the customer at an extra cost.
Get Best QuoteRequest A Callback
Titanium Instrumentation Tube Fittings

Titanium Instrumentation Tube Fittings

Product Price: Rs 150 / PieceGet Best Price

Product Details:
Size38.1 mm
Usage/ApplicationFertilizers Plants
Material GradeUNS R50400
MaterialTitanium
BrandMPJ
Country of OriginMade in India
Thickness25 mm

Titanium Instrumentation Tube Fittings are designed from superior quality of titanium alloy that possesses superior resistance to corrosion and high impact toughness at elevated temperatures. The grade is also recognized as the workhorse of the titanium industry. We, M P Jain Tubing Solutions are fabricating Titanium Instrumentation Tube Fittings, which are performing well in all industrial applications. These Titanium Fittings has numerous beneficial qualities like hardness, rugged construction, unique mechanical properties, high tensile strength, excellent surface finishing, dimensional accuracy, and resistance to corrosion. All these qualities make Titanium Tube Fittings more suitable and convenient for many critical industrial applications.

 

Titanium Compression Tube Fittings, Titanium Gr 2 Instrumentation Fittings, Titanium Gr 2 Compression Fittings, Ti R50400 Instrumentation Tube Fittings Exporter, Ti Grade 2 Tube Fittings, Titanium Alloy Grade 2 Ferrule Fittings, UNS R50400 Titanium Ferrule Tube Fittings Manufacturer in India, Ti Alloy Gr 2 Single Compression Tube Fittings, ASTM B381 Titanium Grade 2 High Pressure Tube Fittings, DIN 3.7035 Titanium Double Ferrule Fittings Suppliers in Mumbai India.


Titanium Instrumentation Tubes Equivalent Grade:

STANDARD

WERKSTOFF NR.

UNS

Titanium Gr.2

3.7035

R50400

Titanium Gr.5

3.7165

N56400

 

Titanium Instrumentation Tubes Chemical Composition:

Grade

Ti

C

Fe

H

N

O

Al

V

Titanium Gr.2

99.2 min

0.1 max

0.3 max

0.015 max

0.03 max

0.25 max

-

-

Titanium Gr.5

90 min

-

0.25 max

-

-

0.2 max

6 min

4 min

 

Titanium Instrumentation Tubes Mechanical Properties:

Element

Density

Melting Point

Tensile Strength

Yield Strength (0.2%Offset)

Elongation

Titanium Gr.2

4.5 g/cm3

1665 °C (3030 °F)

Psi – 49900 , MPa – 344

Psi – 39900 , MPa – 275

20 %

Titanium Gr.5

4.43 g/cm3

1632 °C (2970 °F)

Psi – 138000 , MPa – 950

Psi – 128000 , MPa – 880

14%




Additional Information:

  • Packaging Details: Titanium Instrumentation tube fittings are surface wash and clean to remove all impurities and stock in the warehouse. Then it is wrapped in thin plastic and also it ends are protected by plastic caps to avoid any damage in transit. Titanium Instrumentation tube fittings is bundled in bubble wrap followed by assorting them in colored plastic bundles. An outer rope is tied to protect the tubing and they are packed in wooden box or container. M P Jain Provide Titanium Instrumentation tube fittings with all necessary documents such as commercial invoice, packing list, Test Reports, HS Code, Country of Origin attested by the chamber of commerce, Fumigation Certificate, Warranty Letter, and Base Material Certificates. Every lot is supplied with a material test certificate as per EN 10204 NACE 3.1 standards indicating the chemical and mechanical properties of the Instrumentation Tubes. We also confirm the guarantee of the Titanium Instrumentation tube fittings supplied as per Purchase order specifications and attest the same in the Material Test Certificate. We also welcome any third party inspection from an agency nominated by the customer to comply with NACE 3.2 Certification if required by the customer at an extra cost.
Get Best QuoteRequest A Callback
SMO 254 Instrumentation Tube Fittings

SMO 254 Instrumentation Tube Fittings

Product Price: Rs 175 / PieceGet Best Price

Product Details:
Size38.1 mm
Usage/ApplicationChemical Plants
Material GradeSMO 254
BrandMPJ
Country of OriginMade in India
MaterialSMO 254
Density8.0 g/cm3

M P Jain Tubing Solutions Supplies, manufactures and offers a wide range of 254 SMO Instrumentation Tube Fittings, which is an austenitic stainless steel with high molybdenum content. SMO 254 Instrumentation Tube Fittings is the higher strength austenitic stainless steel alloy fittings that constitute a high level of nickel, nitrogen, chromium, and molybdenum along with low carbon content. We are acknowledged as an Exporter & Manufacturer of WNR. 1.4547 Tube Fittings, it is being offered to our client in a widespread range.   


MO 254 Compression Tube Fittings, DIN 1.4547 Instrumentation Tube Fittings, SMO 254 Instrumentation Fittings Suppliers, Alloy 254 Double Ferrule Tube Fittings, SMO 254 Tube Fittings, 6MOLY Single Ferrule Fittings, UNS S31254 Instrumentation Tube Fittings, SMO 254 Ferrule Fittings Manufacturers in Mumbai, India.

 

ASTM A403 SMO 254 Instrumentation Tube Fittings Grade Specifications:

STANDARD

UNS

WERKSTOFF NR.

AFNOR

EN

JIS

BS

GOST

SMO 254

S31254

1.4547

Z1 CNDU 20.18.06Az

X1CrNiMoCuN20-18-7

2378

-

-

 

Smo 254 Instrumentation Tube Fittings Chemical Composition:

Grade

%

Ni

Cr

Mo

Cu

N

C

Mn

Si

P

S

SMO 254

Min.

17.5

19.5

6

0.5

0.18

-

-

-

-

-

Max.

18.5

20.5

6.5

1

0.22

0.02

1

0.8

0.03

0.01

 

Smo 254 Instrumentation Tube Fittings Mechanical Properties:

Element

Density

Melting Point

Tensile Strength

 

Yield Strength (0.2%Offset)

Elongation

SMO 254

8.0 g/cm3

1320-1390 ???

650

 

300

35



Additional Information:

  • Packaging Details: SMO 254 Instrumentation tube fittings are surface wash and clean to remove all impurities and stock in the warehouse. Then it is wrapped in thin plastic and also it ends are protected by plastic caps to avoid any damage in transit. SMO 254 Instrumentation tube fittings is bundled in bubble wrap followed by assorting them in colored plastic bundles. An outer rope is tied to protect the tubing and they are packed in wooden box or container. M P Jain Provide SMO 254 Instrumentation tube fittings with all necessary documents such as commercial invoice, packing list, Test Reports, HS Code, Country of Origin attested by the chamber of commerce, Fumigation Certificate, Warranty Letter, and Base Material Certificates. Every lot is supplied with a material test certificate as per EN 10204 NACE 3.1 standards indicating the chemical and mechanical properties of the Instrumentation Tubes. We also confirm the guarantee of the SMO 254 Instrumentation tube fittings supplied as per Purchase order specifications and attest the same in the Material Test Certificate. We also welcome any third party inspection from an agency nominated by the customer to comply with NACE 3.2 Certification if required by the customer at an extra cost.
Get Best QuoteRequest A Callback
Brass Instrumentation Tube Fittings

Brass Instrumentation Tube Fittings

Product Price: Rs 180 / PieceGet Best Price

Product Details:
MaterialBrass
Size38.1 mm
Usage/ApplicationPharmaceuticals Industrial
TemperatureMax. 400 Degree C
BrandMPJ
Electrical Resistivity39.90 ohms
Liquidus Melting Point1650 Degree F
Solidus Melting Point1630 Degree F

M P Jain tubing Solutions designs and manufactures a broad range of Brass InstrumentationTube Fittings. We are offering our clients, quality Brass Tubing Fittings that serve the needs of various industries. These tubes are highly resistant to corrosion, abrasion and high temperatures. We offer our Brass Tubing in standard as well as customized specifications as per the client. Brass Instrumentation Tube Fittings are highly appreciated for their bright gold colour. Henceforth, they are appropriate for decorative purposes. But depending on the application it is to be produced for, the chemistry of Brass Transmission Fittings could be modified such that their chemical and mechanical properties are accomplished. While components such as the specified ASTM B16 Brass Compression Fittings are altogether inspected for mechanical properties, including Rockwell hardness, temper, tensile and yield strength, as well as their chemistry, other specifications for more detailed.

 

IS 319 / BS 218 Instrumentation Tube Fittings, Brass IS 319 Male Connector, Brass IS-319 / BS - 218 Ferrule Fittings, Brass IS-319 / BS - 218 Tube Fittings, IS 319 Female Run Tee, BS 218 Female Branch Tee, Brass IS-319 / BS - 218 Bulk Head Male Connector, Brass Grade BS 218 Male Elbow, Brass BS 218 Male Run Tee, Brass IS 319 Male Branch Tee Exporters, Grade IS 319 Brass Female Connector, Grade BS 218 Brass Bulk Head Female Connector, Brass IS-319 / BS - 218 Female Elbow Supplier in Mumbai, India.

 

C2600 Brass Alloy Double Ferrule Tube Fittings Equivalent Grade:

STANDARD

WERKSTOFF NR.

UNS

Brass

934

C36000

 

Brass C23000 Instrumentation Tube Fittings Chemical Composition:

Brass

Cu

Fe

Pb

Zn

Min. /Max.

60.0-63.0

0.35

2.5-3.0

Rem.

Nominal

61.5

-

2.7

35.4

 

Red Brass C23000 Single Ferrule Fittings Mechanical Properties:

Properties

US Customary

Melting Point -Liquidus

1650 F

Melting Point -Solidus

1630 F

Density

0.307 lb/in3at 68 F

Electrical Resistivity

39.90 ohms - cmil/ft @ 68 F

Electrical Conductivity

26 %IACS @ 68 F

Thermal Conductivity

67 Btu · ft/(hr · ft2·oF)at 68F

Modulas of Elasticity in Tension

14000 ksi



Additional Information:

  • Packaging Details: Brass Instrumentation tube fittings are surface wash and clean to remove all impurities and stock in the warehouse. Then it is wrapped in thin plastic and also it ends are protected by plastic caps to avoid any damage in transit. Brass Instrumentation tube fittings is bundled in bubble wrap followed by assorting them in colored plastic bundles. An outer rope is tied to protect the tubing and they are packed in wooden box or container. M P Jain Provide Brass Instrumentation tube fittings with all necessary documents such as commercial invoice, packing list, Test Reports, HS Code, Country of Origin attested by the chamber of commerce, Fumigation Certificate, Warranty Letter, and Base Material Certificates. Every lot is supplied with a material test certificate as per EN 10204 NACE 3.1 standards indicating the chemical and mechanical properties of the Instrumentation Tubes. We also confirm the guarantee of the Brass Instrumentation tube fittings supplied as per Purchase order specifications and attest the same in the Material Test Certificate. We also welcome any third party inspection from an agency nominated by the customer to comply with NACE 3.2 Certification if required by the customer at an extra cost.
Get Best QuoteRequest A Callback
Carbon Steel Instrumentation Tube Fittings

Carbon Steel Instrumentation Tube Fittings

Product Price: Rs 180 / PieceGet Best Price

Product Details:
Size50 mm
Usage/ApplicationPharmaceuticals Industrial
MaterialCarbon Steel
Material GradeASTM A105
BrandMPJ
Country of OriginMade in India
Thickness6.00 mm

M P Jain Tubing Solutions is a largest company of Carbon Steel Instrumentation Tube Fittings as a supplier, stockiest and exporter to our national & international clients. Offering need to providing the high quality of Carbon Steel Instrumentation Tube Fittings to the purchasers, a few testing is directed basically. The testing is done by our expert team having legitimate information on distinguishing the quality of the product. Intergranular corrosion test, pitting resistance test, hardness test, chemical test, mechanical test, positive material identification test are few tests that are conducted on the product.

 

Carbon Steel A105 Instrumentation Fittings, Carbon Steel High Pressure Tube Fittings Traders in India, Carbon Steel Front & Back Ferrule, Carbon Steel Hydraulic Fittings, Carbon Steel Needle Valve Instrumentation Fittings, Carbon Steel Elbow Union with Nut & Ferrule, Carbon Steel Male Connector Stockist, Carbon Steel NPT Manifold Leading Manufacturers, Carbon Steel Bulk Head Female Connector, Carbon Bulk Head Union Adapter, Carbon Steel Union Cross Supplier, Carbon Steel Parker Instrumentation Tube Fittings in Mumbai, India.

 

Carbon Steel A105 Instrumentation Tube Fittings Chemical Properties:

Grade

C

Mn

P

S

Si

Cu

Ni

Cr

Mo

V

Carbon Steel A105

≤0.35

0.60-1.05

≤0.35

≤0.40

0.10-0.35

≤0.40

≤0.40

≤0.30

≤0.12

≤0.08




Additional Information:

  • Packaging Details: Carbon Steel Instrumentation tube fittings are surface wash and clean to remove all impurities and stock in the warehouse. Then it is wrapped in thin plastic and also it ends are protected by plastic caps to avoid any damage in transit. Carbon Steel Instrumentation tube fittings is bundled in bubble wrap followed by assorting them in colored plastic bundles. An outer rope is tied to protect the tubing and they are packed in wooden box or container. M P Jain Provide Carbon Steel Instrumentation tube fittings with all necessary documents such as commercial invoice, packing list, Test Reports, HS Code, Country of Origin attested by the chamber of commerce, Fumigation Certificate, Warranty Letter, and Base Material Certificates. Every lot is supplied with a material test certificate as per EN 10204 NACE 3.1 standards indicating the chemical and mechanical properties of the Instrumentation Tubes. We also confirm the guarantee of the Carbon Steel Instrumentation tube fittings supplied as per Purchase order specifications and attest the same in the Material Test Certificate. We also welcome any third party inspection from an agency nominated by the customer to comply with NACE 3.2 Certification if required by the customer at an extra cost.
Get Best QuoteRequest A Callback
Double Ferrule Tube Fittings

Double Ferrule Tube Fittings

Product Price: Rs 80 / PieceGet Best Price

Product Details:
ApplicationStructure Pipe
Size3 Inch
MaterialStainless Steel
Usage/ApplicationGas Pipe
BrandM P Jain
Country of OriginMade in India
Steel GradeSS316
Double ferrule Tube Fittings are designed, manufactured, and quality controlled to be totally "interchangeable" with the Swagelok brand of tube fittings. Product provide a reliable, leak-proof connection in instrumentation and process tubing systems, The double ferrule design, with the staged sequential swaging action of the ferrules during make-up, Back ferrule make a grip on tube & front ferrule work as sealing on tube, compensates for the variation in tubing materials, hardness, and thickness of the tube wall to provide leak-tight connections in an extensive range of applications. When the nut is tightened, the back ferrule is driven against the tapered rear of the front ferrule. The front ferrule is driven by force into the tapered mouth of the fitting body and creates a primary tubing seal. The back ferrule consistently grips the tube to hold the fitting and tubing firmly in place while the front ferrule forms a full -faced seal on the tapered surface of the body. In the twin-ferrule tube fitting design, the back and front ferrules move axially instead of a rotary motion. No Torque is transferred to the tubing during installation.

Features:
  • Front ferrule creates a seal on the tubing and fitting body.
  • Nut threads are silver plated to eliminate galling.
  • Back ferrule radially provides a grip on the tubing.
Get Best QuoteRequest A Callback
Stainless Steel Condensate Pots

Stainless Steel Condensate Pots

Product Price: Rs 170 / PieceGet Best Price

Product Details:
Usage/ApplicationPetrochemical Steel Plants
BrandMPJ
MaterialSS
Country of OriginMade in India
Length12 Inch
Working pressure6000 PSIG (41.34 MPa)
Steel GradeSS304

M P Jain Tubing solutions is leading supplier, manufacturer, stockists and exporters for high quality Stainless Steel Condensate Pots. The condensate pots are available in a range of materials. Installation can be either vertical or horizontal lines between primary (Flow Meter) or the secondary (transmitter/ gauge) to act as a barrier to the line fluid permitting direct sensing of the flow conditions. Condensate Pots is designed to drain out foreign or residue material from the pipeline thereby guarding critical components of instrumentation system. Generally Steam is passed through Condensation Pots. The major use of SS condensate pots is to increase the accuracy of flow measurement in steam pipelines. These provide an interface between the vapour phase and condensed phase in the impulse line.

 

Stainless Steel Condensate Pots, SS 304 Condensate Pots, 304 Steel Condensate Pots, Grade 304 Stainless Steel Condensate Pots Suppliers, UNS S30400 Condensate Pots, DIN 1.4301 Condensate Pots, SS 304 Seal Pots Manufacturers in Mumbai, India.


Available Length:

  • 8", 10" & 12" & Larger size


Stainless Steel 304 Condensate Pots Equivalent Grade: 

STANDARD

 

WERKSTOFF NR.

 

UNS

JIS

BS

GOST

AFNOR

EN

SS 304

 

1.4301

 

S30400

SUS 304

304S31

08??18??10

Z7CN18???09

X5CrNi18-10

 

Stainless Steel 304 Condensate Pots Chemical Properties: 

Grade

C

Mn

Si

P

S

Cr

Mo

Ni

N

SS 304

0.08 max

2 max

0.75 max

0.045 max

0.030 max

18 – 20

-

8 – 11

-



Additional Information:

  • Packaging Details: Stainless Steel Condenser Pots are surface wash and clean to remove all impurities and stock in the warehouse. Then it is wrapped in thin plastic and also it ends are protected by plastic caps to avoid any damage in transit. Stainless Steel Condenser Pots is bundled in bubble wrap followed by assorting them in colored plastic bundles. An outer rope is tied to protect the tubing and they are packed in wooden box or container. M P Jain Provide Stainless Steel Condenser Pots with all necessary documents such as commercial invoice, packing list, Test Reports, HS Code, Country of Origin attested by the chamber of commerce, Fumigation Certificate, Warranty Letter, and Base Material Certificates. Every lot is supplied with a material test certificate as per EN 10204 NACE 3.1 standards indicating the chemical and mechanical properties of the Instrumentation Tubes. We also confirm the guarantee of the Stainless Steel Condenser Pots supplied as per Purchase order specifications and attest the same in the Material Test Certificate. We also welcome any third party inspection from an agency nominated by the customer to comply with NACE 3.2 Certification if required by the customer at an extra cost.
Get Best QuoteRequest A Callback
Duplex Steel Condensate Pots

Duplex Steel Condensate Pots

Product Price: Rs 1,500 / PieceGet Best Price

Product Details:
Usage/ApplicationRefineries Power Plant
MaterialDuplex Steel
BrandMPJ
Material GradeS32205
Country of OriginMade in India
Length12"
Working pressure6000 PSIG (41.34 MPa)

M P Jain Tubing Solutions is the leading manufacturer, stockist, supplier, and exporter of Duplex Steel Condensate Pots. Duplex Steel condensate pots is known to be the popular alloy in the market for manufacturing good quality of Condensate Pots. This combination offers exceptional protection from corrosion and excellent mechanical strength in high temperature and pressure situations. There are variable grades in Duplex Steel which offers unique specs when utilized. But the most broadly known level of Duplex with regards to when it comes to manufacture the Pots is S31803 and S32205 grades.


SAF 2205 Condensate Pots, DIN 1.4462 Condensate Pots, Duplex Steel Condensate Pots, Duplex Steel S31803 / S32205 Condensate Pots, Grade S32205 Duplex Steel Condensate Pots Suppliers, S31803 Steel Condensate Pots, Duplex Steel S31803/S32205 Seal Pots, Duplex Steel S31803 Seal Pots, DS S31803 Condensate Pot Seal Pot, Duplex Steel S32205 Condensation Pots, Duplex Steel S31803 Seal Pots, Duplex Stainless Steel S32205 NPT Furnished Pots, Grade S31803 Duplex Steel Condensate Seal Pots, Duplex Steel S32205 DRIP Pots, SUS S31803/S32205 2 Ports Condensate Pots, SAF 2205 Condensate Pots Supplier in Mumbai, India.


Duplex Steel S31803 / S32205 Condensate Pots Equivalent Grade:

STANDARD

WERKSTOFF NR.

UNS

Duplex 2205

1.4462

S31803 / S32205

 

Duplex Steel S31803 / S32205 Condensate Pots Chemical Properties:

Grade

C

Mn

Si

P

S

Cr

Mo

Ni

N

Fe

Duplex Steel S31803

0.030 max

1.20 max

0.80 max

0.035 max

0.020 max

24.00 – 26.00

3.00 – 5.00

6.00 – 8.00

0.24 – 0.32

58.095 min

Duplex Steel S32205

0.05 max

1.00 max

1.00 max

0.030 max

0.010 max

24.00 – 26.00

3.00 – 4.00

6.00 – 8.00

0.20 – 0.30

57.61 min



    Additional Information:

    • Packaging Details: Duplex Steel Condenser Pots are surface wash and clean to remove all impurities and stock in the warehouse. Then it is wrapped in thin plastic and also it ends are protected by plastic caps to avoid any damage in transit. Duplex Steel Condenser Pots is bundled in bubble wrap followed by assorting them in colored plastic bundles. An outer rope is tied to protect the tubing and they are packed in wooden box or container. M P Jain Provide Duplex Steel Condenser Pots with all necessary documents such as commercial invoice, packing list, Test Reports, HS Code, Country of Origin attested by the chamber of commerce, Fumigation Certificate, Warranty Letter, and Base Material Certificates. Every lot is supplied with a material test certificate as per EN 10204 NACE 3.1 standards indicating the chemical and mechanical properties of the Instrumentation Tubes. We also confirm the guarantee of the Duplex Steel Condenser Pots supplied as per Purchase order specifications and attest the same in the Material Test Certificate. We also welcome any third party inspection from an agency nominated by the customer to comply with NACE 3.2 Certification if required by the customer at an extra cost.
    Get Best QuoteRequest A Callback
    Nickel 200 Condensate Pots

    Nickel 200 Condensate Pots

    Product Price: Rs 250 / KilogramGet Best Price

    Product Details:
    Material GradeNickel 200
    Usage/ApplicationChemical Plants
    Thickness5 mm
    ColorSilver
    MaterialNickel alloy
    Length10"
    Working pressure6000 PSIG (41.34 MPa)
    BrandMPJ

    M P Jain tubing Solution is the known in manufacturing, suppling and exporter of the nickel condensate pots. The nickel 200 condensate pots are basically devices that allow flowing of liquid between the flowing of gases and instrument like steam. The key capacity of the condensate pots is to keep up the degree of fluid in motivation tubes. It can be utilized where it is viscous or corrosive in nature. The establishment of the condensate pots is actually quite simple and it can without much of a stretch be kept up and the cleaning is simple. The condensate pots are valuable in applications that require weight and high temperature. Nickel pot can be gotten to in different surface finishes, grades, and material as per with industrial specifications and norms.  M P Jain tubing Solution supply this high-quality Nickel 200 condensate pots at affordable rates. We are known to offer top notch quality of condensate pots using the nickel alloy.

     

    Nickel 200 Condensate Seal Chambers, UNS N02200 Condensate Pots, Nickel 200 Condensate Seal Pots DIN 2.4066 Condensate Pots, Alloy 200 Seal Pots Suppliers, Nickel Alloy 200 Condensate Pots, Nickel Alloy 200 Condensate Pot Manufacturers, Nickel 200 Condensate Chamber, Nickel Alloy 200 Seal Pots Exporters, Nickel Alloy 200 NPT Condensate Pots Exporter.

     

    Nickel 200 Condensate Pots Equivalent Grade:

    STANDARD

    WNR.

    UNS

    JIS

    BS

    GOST

    AFNOR

    EN

    Nickel Alloy 200

    2.4066

    N02200

    NW 2200

    NA 11

    ????-2

    N-100M

    Ni 99.2

     

    Nickel 200 Condensate Pots Chemical Properties:

    Grade

    C

    Mn

    Si

    S

    Cu

    Fe

    Ni

    Nickel 200

    0.15 max

    0.35 max

    0.35 max

    0.01 max

    0.25 max

    0.40 max

    99.0 min



    Additional Information:

    • Packaging Details: Nickel 200 Condenser Pots are surface wash and clean to remove all impurities and stock in the warehouse. Then it is wrapped in thin plastic and also it ends are protected by plastic caps to avoid any damage in transit. Nickel 200 Condenser Pots is bundled in bubble wrap followed by assorting them in colored plastic bundles. An outer rope is tied to protect the tubing and they are packed in wooden box or container. M P Jain Provide Nickel 200 Condenser Pots with all necessary documents such as commercial invoice, packing list, Test Reports, HS Code, Country of Origin attested by the chamber of commerce, Fumigation Certificate, Warranty Letter, and Base Material Certificates. Every lot is supplied with a material test certificate as per EN 10204 NACE 3.1 standards indicating the chemical and mechanical properties of the Instrumentation Tubes. We also confirm the guarantee of the Nickel 200 Condenser Pots supplied as per Purchase order specifications and attest the same in the Material Test Certificate. We also welcome any third party inspection from an agency nominated by the customer to comply with NACE 3.2 Certification if required by the customer at an extra cost.
    Get Best QuoteRequest A Callback
    Monel 400 Condensate Pots

    Monel 400 Condensate Pots

    Product Price: Rs 1,500 / PieceGet Best Price

    Product Details:
    Usage/ApplicationPetrochemical Steel Plants
    BrandMPJ
    Material GradeMonel 400
    MaterialMonel
    Length12"
    Working pressure6000 PSIG (41.34 MPa)
    Country of OriginMade in India

    M P Jain Tubing Solutions is the known supplier, exporter and manufacturer of Monel 400 Condensate pots. Monel 400 Condensate Pots are designed to drain out foreign material from the pipeline while protecting critical components of any instrumentation system. Mainly, steam is passed through the condensate pots. These are also known as condensate chambers, condensing pots or seal pots.These pots are manufactured using the high temperature, heat resistance and tested raw materials that contribute to wide usage in the engineering applications. These pots possess exceptional properties such as erosion-corrosion resistance, high abrasion resistance, and durability. These condensate pots are widely used in many applications especially in the marine and chemical processing industries.

     

    DIN 2.4360 Condensate Pots, Monel 400 Condensate Pot Suppliers, Monel Alloy 400 Seal Pots, Monel 400 Condensate Chamber, Monel Alloy Condensate Pots, Monel 400 Condensate Seal Pots, Monel 400 Condensate Seal Chambers, Monel 400 NPT Condensate Pots, Alloy 400 Seal Pots, Monel Alloy 400 Condensate Pots, UNS N04400 Condensate Pots, Monel Condensate Pots Suppliers in Mumbai, India.

     

    Monel 400 Condensate Pots equivalent grades:

    STANDARD

    UNS

    WNR.

    JIS

    BS

    GOST

    AFNOR

    EN

    Monel 400

    N04400

    2.4360

    NW 4400

    NA 13

    ?????????? 28-2,5-1,5

    NU-30M

    NiCu30Fe

     

    Monel 400 Condensate Pots Chemical Properties:

    Grade

     

    C

    Mn

    Si

    S

    Cu

    Fe

    Ni

    Monel 400

     

    0.30 max

    2.00 max

    0.50 max

    0.024 max

    28.00 – 34.00

    2.50 max

    63.00 min



    Additional Information:

    • Packaging Details: Monel 400 Condenser Pots are surface wash and clean to remove all impurities and stock in the warehouse. Then it is wrapped in thin plastic and also it ends are protected by plastic caps to avoid any damage in transit. Monel 400 Condenser Pots is bundled in bubble wrap followed by assorting them in colored plastic bundles. An outer rope is tied to protect the tubing and they are packed in wooden box or container. M P Jain Provide Monel 400 Condenser Pots with all necessary documents such as commercial invoice, packing list, Test Reports, HS Code, Country of Origin attested by the chamber of commerce, Fumigation Certificate, Warranty Letter, and Base Material Certificates. Every lot is supplied with a material test certificate as per EN 10204 NACE 3.1 standards indicating the chemical and mechanical properties of the Instrumentation Tubes. We also confirm the guarantee of the Monel 400 Condenser Pots supplied as per Purchase order specifications and attest the same in the Material Test Certificate. We also welcome any third party inspection from an agency nominated by the customer to comply with NACE 3.2 Certification if required by the customer at an extra cost.
    Get Best QuoteRequest A Callback
    Inconel 600 Condensate Pots

    Inconel 600 Condensate Pots

    Product Price: Rs 50 / KilogramGet Best Price

    Product Details:
    Usage/ApplicationFood Industries
    BrandMPJ
    Material GradeInconel 600
    ColorSilver
    ShapeCylindrical
    Length12"
    MaterialInconel
    Working Pressure6000 PSIG (41.34 MPa)

    M P Jain Tubing Solutions is one of the largest supplier, manufacturer, and exporter of Inconel 400 Condensate pots. Inconel 600 Condensate Pots are formed with the Inconel alloy that is chromium-nickel alloy grade that is mainly used in those circumstances where high temperature and corrosion resistance is required. The presence of nickel alloy ensures to retain substantial resistance under decreasing circumstances. These pots are generally non-magnetic and exhibit good mechanical properties. Furthermore, these are immune to chloride ion stress corrosion cracking and provide outstanding resistance to alkaline solutions. However, these pots excellently resist ammonia bearing environments as well as carburizing and nitrogen gases. The alloy of pots is both cold and hot formed through the typical processes of fabrication. Hence the hot working is executed at a temperature of 1600-2250 degree F. However the alloy 600 is not age hardening but to improve its corrosion resistance these are soft annealed followed through forging.

     

    Grade 600 Inconel Condensate Pots, Inconel 600 Condensate Pots, Inconel 600 Condensate Seal Chambers, DIN 2.4816 Condensate Pots, Inconel Alloy 600 Seal Pots, Inconel 600 Condensate Seal Pots, Inconel Alloy 600 Condensate Chamber, Alloy 600 Seal Pots, UNS N06600 Condensate Pots, Inconel 600 Condensate Pots, Alloy 600 Condensate Pots Manufacturers in Mumbai, India.

     

    Inconel 600 Condensate Pots equivalent grade: 

    STANDARD

    UNS

    WERKSTOFF NR.

    JIS

    AFNOR

    BS

    GOST

    EN

    Alloy 600

    N06600

    2.4816

    NCF 600

    NC15FE11M

    NA 13

    ?????????? 28-2,5-1,5

    NiCr15Fe

     

    Inconel 600 Condensate Pots chemical properties:

    Grade

    Ni

    Cr

    Fe

    C

    Mn

    S

    Si

    Cu

    Inconel 600

    72.0 min

    14.0 – 17.0

    6.0 – 10.0

    0.15 max

    1.0 max

    0.015 max

    0.5 max

    0.5 max



    Additional Information:

    • Packaging Details: Inconel 600 Condenser Pots are surface wash and clean to remove all impurities and stock in the warehouse. Then it is wrapped in thin plastic and also it ends are protected by plastic caps to avoid any damage in transit. Inconel 600 Condenser Pots is bundled in bubble wrap followed by assorting them in colored plastic bundles. An outer rope is tied to protect the tubing and they are packed in wooden box or container. M P Jain Provide Inconel 600 Condenser Pots with all necessary documents such as commercial invoice, packing list, Test Reports, HS Code, Country of Origin attested by the chamber of commerce, Fumigation Certificate, Warranty Letter, and Base Material Certificates. Every lot is supplied with a material test certificate as per EN 10204 NACE 3.1 standards indicating the chemical and mechanical properties of the Instrumentation Tubes. We also confirm the guarantee of the Inconel 600 Condenser Pots supplied as per Purchase order specifications and attest the same in the Material Test Certificate. We also welcome any third party inspection from an agency nominated by the customer to comply with NACE 3.2 Certification if required by the customer at an extra cost.
    Get Best QuoteRequest A Callback
    Hastelloy C22 Condensate Pots

    Hastelloy C22 Condensate Pots

    Product Price: Rs 180 / PieceGet Best Price

    Product Details:
    Material GradeHastelloy C22
    MaterialHastelloy
    Werkstoff Nr2.4602
    BrandMPJ
    Length12"
    Working pressure6000 PSIG (41.34 MPa)

    M P Jain Tubing Solution is an exceptionally acclaimed and esteemed firm that gives qualitative range of Hastelloy C22 Condensate Pots to their regard customers. Hastelloy C22 Condensate Pots are designed from the austenitic chromium-molybdenum-nickel alloy including with tungsten content. These are the versatile pots that enhance superior resistance to stress corrosion cracking, crevice and pitting corrosion in harsh climatic circumstances. These combinations of pots are exceptionally impervious to forceful conditions. The high chromium content conveys better obstruction than different oxidizing media while the nickel combination has better opposition than oxidizing watery media that incorporates chlorides, formic and acidic acids, and wet chlorines. Moreover, the nickel alloy excellently resists the formation of grain boundary precipitates in the weld heat affected zone.

     

    Hastelloy Alloy C22 Condensate Pot Seal Pot, Alloy C22 2 Ports Condensate Pots, DIN 2.4602 Condensate Pots, Grade C22 Hastelloy Condensate Pots, Alloy C22 Condensation Pots, Grade C22 Hastelloy Condensate Seal Pots, Hastelloy C22 Seal Pots, Hastelloy Alloy C22 Seal Pots C22 Steel Condensate Pots, Hastelloy C22 Condensate Pots, Hastelloy Condensate Pots, Hastelloy Condensate Pots, Hastelloy C22 DRIP Pots, Hastelloy C22 Condensate Pots UNS N06022 Condensate Pots, Alloy C22 Seal Pots Supplier in Mumbai, India.

     

    Hastelloy C22 Condensate Pots equivalent grade:

    STANDARD

    WERKSTOFF NR.

    UNS

    JIS

    GOST

    EN

    OR

     C22

    2.4602

    N06022

    NW 6022

    NiCr21Mo14W

     

    Hastelloy C22 Condensate Pots Chemical Properties:

    Grade

    C

    Mn

    Si

    S

    Co

    Ni

    Cr

    Fe

    Mo

    P

    C22

    0.010 max

    0.50 max

    0.08 max

    0.02 max

    2.50 max

    50.015 min*

    20.00 – 22.50

    2.00 – 6.00

    12.50 – 14.50

    0.02 max



    Additional Information:

    • Packaging Details: Hastelloy C22 Condenser Pots are surface wash and clean to remove all impurities and stock in the warehouse. Then it is wrapped in thin plastic and also it ends are protected by plastic caps to avoid any damage in transit. Hastelloy C22 Condenser Pots is bundled in bubble wrap followed by assorting them in colored plastic bundles. An outer rope is tied to protect the tubing and they are packed in wooden box or container. M P Jain Provide Hastelloy C22 Condenser Pots with all necessary documents such as commercial invoice, packing list, Test Reports, HS Code, Country of Origin attested by the chamber of commerce, Fumigation Certificate, Warranty Letter, and Base Material Certificates. Every lot is supplied with a material test certificate as per EN 10204 NACE 3.1 standards indicating the chemical and mechanical properties of the Instrumentation Tubes. We also confirm the guarantee of the Hastelloy C22 Condenser Pots supplied as per Purchase order specifications and attest the same in the Material Test Certificate. We also welcome any third party inspection from an agency nominated by the customer to comply with NACE 3.2 Certification if required by the customer at an extra cost.
    Get Best QuoteRequest A Callback
    Titanium Condensate Pots

    Titanium Condensate Pots

    Product Price: Rs 8,000 / PieceGet Best Price

    Product Details:
    Usage/ApplicationRefineries Power Plant
    FinishingPolish
    BrandMPJ
    ShapeCylindrical
    MaterialTitanium
    Length12"
    Working Pressure6000 PSIG (41.34 MPa)

    M P Jain tubing Solution is completely associated with offering the best quality of Titanium Gr 2 Condensate Pots so all applications requires are effectively fulfilled. We as holding excellent long periods of working experience are in this manner ready to offer to the buyers the products at uniquely designed details as per the necessities. We as a client driven and so as to satisfy all the requests of worldwide and private purchasers are offering the equivalent in various details that vary in sizes, standard, measurements, and so on. Also to bring out the stunning the quality of pots that could assure 100% perfect dimensional accuracy and fine surface finishes, development is executed by using advanced technology and modern machinery. It is supplied to the buyers well on time and in good condition. We are making effective usage of superior quality of raw materials that is checked before manufacture. In order to fabricate the product of superior quality the acquired material is well tested. The product is designed according to set assembling standards of the business and public and worldwide product quality guidelines.

     

    Titanium Gr. 2 Condensate Pots, Ti Gr 2 Steel Condensate Pots, UNS R50400 Condensate Pots, DIN 3.7035 Condensate Pots, Titanium Gr. 2 Condensate Seal Chambers, Alloy Gr 2 Condensate Pots, Ti Alloy Gr 2 Condensate Pots, Titanium Gr 2 Condensate Seal Pots, Titanium Alloy Gr 2 Seal Pots, Titanium Alloy Gr 2 Condensate Chamber, Grade 2 Titanium Condensate Pots Suppliers, Alloy Gr 2 Seal Pots, Titanium Grade 2 Condensate Pots Manufacturers in Mumbai, India.

     

    Titanium Condensate Pots Equivalent grade:

    STANDARD

    WERKSTOFF NR.

    UNS

    Titanium Grade 2

    3.7035

    R50400

     

    Titanium Condensate Pots Chemical Properties:

    Grade

    Ti

    C

    Fe

    H

    N

    O

    Al

    V

    Ti Grade 2

    99.2 min

    0.1 max

    0.3 max

    0.015 max

    0.03 max

    0.25 max




    Additional Information:

    • Packaging Details: Titanium Condenser Pots are surface wash and clean to remove all impurities and stock in the warehouse. Then it is wrapped in thin plastic and also it ends are protected by plastic caps to avoid any damage in transit. Titanium Condenser Pots is bundled in bubble wrap followed by assorting them in colored plastic bundles. An outer rope is tied to protect the tubing and they are packed in wooden box or container. M P Jain Provide Titanium Condenser Pots with all necessary documents such as commercial invoice, packing list, Test Reports, HS Code, Country of Origin attested by the chamber of commerce, Fumigation Certificate, Warranty Letter, and Base Material Certificates. Every lot is supplied with a material test certificate as per EN 10204 NACE 3.1 standards indicating the chemical and mechanical properties of the Instrumentation Tubes. We also confirm the guarantee of the Titanium Condenser Pots supplied as per Purchase order specifications and attest the same in the Material Test Certificate. We also welcome any third party inspection from an agency nominated by the customer to comply with NACE 3.2 Certification if required by the customer at an extra cost.
    Get Best QuoteRequest A Callback
    Bulkhead Male Connector

    Bulkhead Male Connector

    Product Price: Rs 90 / PieceGet Best Price

    Product Details:
    MaterialSS
    Usage/ApplicationHydraulic Pipe
    Size3/4"
    Pressure6000 psi (413 bar)
    BrandMPJ
    Country of OriginMade in India
    Connector SeriesSMA
    Connector GenderMale

    Male Bulkhead Connector has an interface type of solder cup and a 50 Ohm impedance. Pasternack Male bulkhead Connector uses shield/contact solder as an attachment method. Our Male Connector provides a minimum frequency of DC and a maximum frequency of 18 GHz.

    The Pasternack Male Bulkhead Connector has a teflon dielectric type and a VSWR of 1.23. The Pasternack SMA terminal connector has a passivated stainless steel body. Our PE4354 Connector uses brass contact. This Male bulkhead terminal RF connector is RoHS and REACH compliant.

    This Pasternack Male Bulkhead Connector will ship the same day as purchased. Our bulkhead Male Connector is part of over 40,000 RF, microwave and millimeter wave components in stock for worldwide shipment. We also build custom Connector cable assemblies that will ship the same day as well.


    Male Bulkhead Connector Stockist, Copper Nickel Union Fittings, Male Bulkhead Connector Tubing, Stainless Steel Male Bulkhead Connector Fittings Stockist, Carbon Steel Male Bulkhead Connector Pipe Fittings, Ss 316 Male Bulkhead Connector Fittings,Most Recognized Male Bulkhead Connector Pipe Fitting Manufacturer, Male Bulkhead Connector Adapter, Cu-ni 70/30 Male Bulkhead Connector Fittings Stockholder, Nickel Alloy Male Bulkhead Connector Fittings, Male Bulkhead Connector Exporter, Male Bulkhead Connector With Ferrule Fittings Supplier, Male Bulkhead Connector Instrumentation Pipe Fitting, Alloy Steel Male Bulkhead Connector Pipes Fittings Exporter, Cu-ni 90/10 Male Bulkhead Connector, Ss 304 Male Bulkhead Connector.

    Additional Information:

    • Delivery Time: Ready Stock
    Get Best QuoteRequest A Callback
    Male Elbow NPT

    Male Elbow NPT

    Product Price: Rs 130 / PieceGet Best Price

    Product Details:
    Elbow Bend Angle90 degree
    End Connection TypeBSP
    Size1/4"
    Usage/ApplicationHydraulic Pipe
    MaterialBrass
    BrandMPJ
    Country of OriginMade in India
    Outer Diameter3/8 inch
    Working pressure3100 PSI

    NPT (National Pipe Thread) seals are the most popular type of seal for pressure calibration systems in the U.S. and Canada. NPT male adapters have a taper thread that wedges into the female NPT adapter. They seal due to the "out of roundness principle" which means that the male stretches the female fitting until there is so much force that the connection can hold pressure. One of the challenges with this design is that if you connect stainless steel to stainless steel then over-tightening or poor lubrication can cause gauling and damage to the threads. Thread sealant is needed to seal but only 2 turns of thread sealant is required. Any more than that and the seal can leak around the thread sealant. Mcneil Instruments Inc has a wide variety of male NPT adapters , male Quick-disconnect NPT adapters, male NPT calibrator adapters, female NPT adapters, female NPT gauge adapters and female Quick-disconnect NPT gauge adapters.

    Quickly connect a pressure calibrator or other pressure device with Female NPT connections to Ralston hand pumps or nitrogen calibration equipment




    Additional Information:

    • Delivery Time: Ready Stock
    Get Best QuoteRequest A Callback
    Male Connector NPT

    Male Connector NPT

    Product Price: Rs 100 / PieceGet Best Price

    Product Details:
    Size1/4"
    Pressure6000 psi (413 bar)
    Connection TypeBSPT
    Packaging TypeBox
    Usage/ApplicationGas Pipe
    BrandMPJ
    Country of OriginMade in India

    NPT (National Pipe Thread) seals are the most popular type of seal for pressure calibration systems in the U.S. and Canada. NPT male adapters have a taper thread that wedges into the female NPT adapter. They seal due to the "out of roundness principle" which means that the male stretches the female fitting until there is so much force that the connection can hold pressure. One of the challenges with this design is that if you connect stainless steel to stainless steel then over-tightening or poor lubrication can cause gauling and damage to the threads. Thread sealant is needed to seal but only 2 turns of thread sealant is required. Any more than that and the seal can leak around the thread sealant. Mcneil Instruments Inc has a wide variety of male NPT adapters , male Quick-disconnect NPT adapters, male NPT calibrator adapters, female NPT adapters, female NPT gauge adapters and female Quick-disconnect NPT gauge adapters.

    Quickly connect a pressure calibrator or other pressure device with Female NPT connections to Ralston hand pumps or nitrogen calibration equipment



    Additional Information:

    • Delivery Time: Ready Stock
    Get Best QuoteRequest A Callback
    Bulkhead Union Elbow

    Bulkhead Union Elbow

    Product Price: Rs 80 / PieceGet Best Price

    Product Details:
    End Connection TypeBSPT
    Size3/4"
    BrandMPJ
    MaterialStainless Steel
    Country of OriginMade in India
    Working Pressure6000 psi (413 bar)
    Temperature RatingPTFE 450 Degree f (232 Degree c),Grafoil 700 Degree f (371 Degree c)

    We manufacture, supply and export Bulkhead Union Elbow Fittings which are very useful in various types of connecting functions in the big industries. Our Reducing Union Elbow fittings are of four types to be used in many different works in the varied industries.

    Our in-house production of Bulkhead Union Elbow is manufactured with excellent quality of raw materials to suit the fixing work mainly in electrical industries, air conditioning industries. These products of ours have been well demanded and extensively used by the clients of diverse category in different size. These Elbow have part numbers of numerous kinds to select from.


    Bulkhead Union Elbow Instrumentation Pipe Fitting, Stainless Steel Bulkhead Union Elbow Fittings Stockist,Most Prominent Bulkhead Union Elbow Pipe Fitting Manufacturer, Bulkhead Union Elbow Connector, Alloy Steel Bulkhead Union Elbow Pipes Fittings Exporter, Bulkhead Union Elbow With Ferrule Fittings Supplier, Bulkhead Union Elbow Tubing, Carbon Steel Bulkhead Union Elbow Pipe Fittings, Nickel Alloy Bulkhead Union Elbow Fittings, Bulkhead Union Elbow Adapter, Bulkhead Union Elbow Stockist.

    Specifications:
    • 1/4" , 1/2" & 3/4"  Custom size available as per requirement
    • NPT, BSPT, BSP & Socket Weld.


    Additional Information:

    • Delivery Time: Ready Stock
    Get Best QuoteRequest A Callback
    Stainless Steel Bulkhead Union

    Stainless Steel Bulkhead Union

    Product Price: Rs 120 / PieceGet Best Price

    Product Details:
    Size3/4"
    MaterialStainless Steel
    Connection TypeNPT
    Usage/ApplicationHydraulic Pipe
    Pressure6000 psi (413 bar)
    BrandMPJ
    Country of OriginMade in India

    We manufacture, supply and export Bulkhead Union Fittings which are very useful in various types of connecting functions in the big industries. Our Reducing Union fittings are of four types to be used in many different works in the varied industries.


    Our in-house production of Bulkhead Union is manufactured with excellent quality of raw materials to suit the fixing work mainly in electrical industries, air conditioning industries. These products of ours have been well demanded and extensively used by the clients of diverse category in different size. These Cross have part numbers of numerous kinds to select from.


    Grades:
    • Monel: Grade: Monel 400, Monel K500, Monel R-405
    • Nickel: Grade: Nickel 200, Nickel 201
    • Inconel: Grade: Inconel 600, Inconel 601, Inconel 625, Inconel 718
    • Incoloy: Grade: Incoloy 800, Inconel 800H, 800HT
    • Hastalloy: Grade: Hastalloy B2, Hastalloy B3, Hastalloy C22, Hastalloy C276, Hastalloy X
    • Titanium: Grade: Gr1, Gr2, Gr3, Gr5, Gr7, Gr11
    • Stainless Steel: Grade: ASME / ASTM SA / A403 SA / A 774 WP-S, WP-W, WP-WX, 304, 304L, 316, 316L, 304/304L, 304H, 316H, 316/316L, 321, 330, 347, 309/S, 310/S, 317/L, 333, 410/S, DIN 1.4301, DIN1.4306, DIN 1.4401, DIN 1.4404
    • Carbon Steel: Grade: ASTM A 234 WPB , WPBW, WPHY 42, WPHY 46, WPHY 52, WPH 60, WPHY 65 & WPHY 70
    • Duplex Steel: Grade: ASTM / ASME A/SA 182 UNS F44, F45, F51, F53, F55, F60, F61

    Specifications:
    • 1/4" , 1/2" & 3/4"  Custom size available as per requirement
    • NPT, BSPT, BSP & Socket Weld.


    Additional Information:

    • Delivery Time: Ready Stock
    Get Best QuoteRequest A Callback
    Straight Union Connector

    Straight Union Connector

    Product Price: Rs 100 / PieceGet Best Price

    Product Details:
    Size2 inch
    Usage/ApplicationPlumbing Pipe
    Steel GradeSS304
    ConnectionNPT
    BrandMPJ
    MaterialStainless Steel
    Country of OriginMade in India

    We are the reliable and the most trusted name in manufacturing and providing wide range of Straight Union. These fittings are of premium quality and are highly durable which enables your machinery to work efficiently. These fittings are manufactured by premium quality metals and alloys with special coating to avoid corrosion or decay which ensure better contact between pipe and these fittings to provide a consistent and uninterrupted flow within the system. These fittings are available in different sizes, shapes, thickness and other dimensions as per allotted by our prestigious clients.

    We provide various types of fittings such as fittings of steel and its alloys, fittings of copper and its alloys etc. These fittings are leak proof with life long warranty without compromising with the strength of these fittings. Along with all other qualities, our fittings are highly appreciated for their superior finish with sophisticated and sleek design.


    Straight Union Connector, Straight Union Adapter, Carbon Steel Straight Union Pipe Fittings, Stainless Steel Straight Union Fittings Stockist, Nickel Alloy Straight Union Fittings, Cu-ni 90/10 Straight Union Fittings Stockholder, Straight Union With Ferrule Fittings Supplier, Copper Nickel Union Fittings, Ss 316 Straight Union Fittings,Most Prominent Straight Union Pipe Fitting Manufacturer, Straight Union Instrumentation Pipe Fitting, Straight Union Tubing, Straight Union Coupling, Alloy Steel Straight Union Pipes Fittings Exporter, Ss 304 Straight Union.

    Grades:
    • Monel: Grade: Monel 400, Monel K500, Monel R-405
    • Nickel: Grade: Nickel 200, Nickel 201
    • Inconel: Grade: Inconel 600, Inconel 601, Inconel 625, Inconel 718
    • Incoloy: Grade: Incoloy 800, Inconel 800H, 800HT
    • Hastalloy: Grade: Hastalloy B2, Hastalloy B3, Hastalloy C22, Hastalloy C276, Hastalloy X
    • Titanium: Grade: Gr1, Gr2, Gr3, Gr5, Gr7, Gr11
    • Stainless Steel: Grade: ASME / ASTM SA / A403 SA / A 774 WP-S, WP-W, WP-WX, 304, 304L, 316, 316L, 304/304L, 304H, 316H, 316/316L, 321, 330, 347, 309/S, 310/S, 317/L, 333, 410/S, DIN 1.4301, DIN1.4306, DIN 1.4401, DIN 1.4404
    • Carbon Steel: Grade: ASTM A 234 WPB , WPBW, WPHY 42, WPHY 46, WPHY 52, WPH 60, WPHY 65 & WPHY 70
    • Duplex Steel: Grade: ASTM / ASME A/SA 182 UNS F44, F45, F51, F53, F55, F60, F61


      Additional Information:

      • Delivery Time: Ready Stock
      Get Best QuoteRequest A Callback
      NPT Connector

      NPT Connector

      Product Price: Rs 125 / PieceGet Best Price

      Product Details:
      MaterialSS
      Size1/2"
      ApplicationGas Pipe
      BrandMPJ
      Connector TypeNPT
      Maximum Working Pressure6000 psi (413 bar)
      Country of OriginMade in India

      NPT (National Pipe Thread) seals are the most popular type of seal for pressure calibration systems in the U.S. and Canada. NPT male adapters have a taper thread that wedges into the female NPT adapter. They seal due to the "out of roundness principle" which means that the male stretches the female fitting until there is so much force that the connection can hold pressure. One of the challenges with this design is that if you connect stainless steel to stainless steel then over-tightening or poor lubrication can cause gauling and damage to the threads. Thread sealant is needed to seal but only 2 turns of thread sealant is required. Any more than that and the seal can leak around the thread sealant. Mcneil Instruments Inc has a wide variety of male NPT adapters , male Quick-disconnect NPT adapters, male NPT calibrator adapters, female NPT adapters, female NPT gauge adapters and female Quick-disconnect NPT gauge adapters.

      Quickly connect a pressure calibrator or other pressure device with Female NPT connections to Ralston hand pumps or nitrogen calibration equipment

      Steel Grades
      • Monel: Grade: Monel 400, Monel K500, Monel R-405
      • Nickel: Grade: Nickel 200, Nickel 201
      • Inconel: Grade: Inconel 600, Inconel 601, Inconel 625, Inconel 718
      • Incoloy: Grade: Incoloy 800, Inconel 800H, 800HT
      • Hastalloy: Grade: Hastalloy B2, Hastalloy B3, Hastalloy C22, Hastalloy C276, Hastalloy X
      • Titanium: Grade: Gr1, Gr2, Gr3, Gr5, Gr7, Gr11
      • Stainless Steel: Grade: ASME / ASTM SA / A403 SA / A 774 WP-S, WP-W, WP-WX, 304, 304L, 316, 316L, 304/304L, 304H, 316H, 316/316L, 321, 330, 347, 309/S, 310/S, 317/L, 333, 410/S, DIN 1.4301, DIN1.4306, DIN 1.4401, DIN 1.4404
      • Carbon Steel: Grade: ASTM A 234 WPB , WPBW, WPHY 42, WPHY 46, WPHY 52, WPH 60, WPHY 65 & WPHY 70
      • Duplex Steel: Grade: ASTM / ASME A/SA 182 UNS F44, F45, F51, F53, F55, F60, F61

      Specifications:
      • 1/4" , 1/2" & 3/4"  Custom size available as per requirement
      • NPT, BSPT, BSP & Socket Weld.


      Additional Information:

      • Delivery Time: READY STOCK
      Get Best QuoteRequest A Callback
      Stainless Steel Hydraulic Fitting

      Stainless Steel Hydraulic Fitting

      Product Price: Rs 250 / PieceGet Best Price

      Product Details:
      Size3"
      Usage/ApplicationHydraulic Pipe
      BrandM P Jain
      ApplicationMachinery
      MaterialStainless Steel
      ColorSilver
      Country of OriginMade in India
      Steel GradeSS304
      We are offering Stainless Steel Hydraulic Fitting to our client.
      Get Best QuoteRequest A Callback
      Male Run Tee

      Male Run Tee

      Product Price: Rs 130 / PieceGet Best Price

      Product Details:
      Size3/4"
      Usage/ApplicationGas Pipe
      End Connection TypeNPT
      BrandMPJ
      Thread Size1/2 inch
      ConnectionMale
      Working Pressure3100 PSI
      MaterialBrass
      Country of OriginMade in India

      We manufacture, supply and export Male Run Tee Fittings which are very useful in various types of connecting functions in the big industries. Our Male Run Tee fittings are of four types to be used in many different works in the varied industries.

      Our in-house production of Male Run Tee is manufactured with excellent quality of raw materials to suit the fixing work mainly in electrical industries, air conditioning industries. These products of ours have been well demanded and extensively used by the clients of diverse category in different size. These Male Run Tee have part numbers of numerous kinds to select from.


      Copper Nickel Union Fittings, Female Run Tee Connector, Carbon Steel Female Run Tee Pipe Fittings, Female Run Tee Stockist, Female Run Tee Instrumentation Pipe Fitting, Nickel Alloy Female Run Tee Fittings, Female Run Tee With Ferrule Fittings Supplier, Stainless Steel Female Run Tee Fittings Stockist, Ss 304 Male Run Tee, Cu-ni 70/30 Male Run Tee Fittings Stockholder, Alloy Steel Female Run Tee Pipes Fittings Exporter ,Most Recognized Female Run Tee Pipe Fitting Manufacturer, Cu-ni 90/10 Female Run Tee Fittings Stockholder, Ss 316 Male Run Tee Fittings, Copper Nickel Union Fittings, Female Run Tee Adapter, Ss 304 Female Run Tee, Cu-ni 90/10 Male Run Tee, Ss 316 Female Run Tee Fittings, Female Run Tee Tubing.

      Grades:

      • Monel: Grade: Monel 400, Monel K500, Monel R-405
      • Nickel: Grade: Nickel 200, Nickel 201
      • Inconel: Grade: Inconel 600, Inconel 601, Inconel 625, Inconel 718
      • Incoloy: Grade: Incoloy 800, Inconel 800H, 800HT
      • Hastalloy: Grade: Hastalloy B2, Hastalloy B3, Hastalloy C22, Hastalloy C276, Hastalloy X
      • Titanium: Grade: Gr1, Gr2, Gr3, Gr5, Gr7, Gr11
      • Stainless Steel: Grade: ASME / ASTM SA / A403 SA / A 774 WP-S, WP-W, WP-WX, 304, 304L, 316, 316L, 304/304L, 304H, 316H, 316/316L, 321, 330, 347, 309/S, 310/S, 317/L, 333, 410/S, DIN 1.4301, DIN1.4306, DIN 1.4401, DIN 1.4404
      • Carbon Steel: Grade: ASTM A 234 WPB , WPBW, WPHY 42, WPHY 46, WPHY 52, WPH 60, WPHY 65 & WPHY 70
      • Duplex Steel: Grade: ASTM / ASME A/SA 182 UNS F44, F45, F51, F53, F55, F60, F61

      Specifications:
      • 1/4" , 1/2" & 3/4"  Custom size available as per requirement
      • NPT, BSPT, BSP & Socket Weld.


      Additional Information:

      • Delivery Time: READY STOCK
      Get Best QuoteRequest A Callback
      High Pressure Union Elbow

      High Pressure Union Elbow

      Product Price: Rs 150 / PieceGet Best Price

      Product Details:
      MaterialSS
      Connection TypeNPT
      Usage/ApplicationGas Pipe
      Pressure6000 psi (413 bar)
      Packaging TypeBox
      Place Of OriginIndia
      BrandMPJ
      Size3/4"
      Country of OriginMade in India

      We manufacture, supply and export Union Fittings which are very useful in various types of connecting functions in the big industries. Our union fittings are of four types to be used in many different works in the varied industries.

      Our in-house production of Union Elbow is manufactured with excellent quality of raw materials to suit the fixing work mainly in electrical industries, air conditioning industries. These products of ours have been well demanded and extensively used by the clients of diverse category in different size. These Elbows have part numbers of numerous kinds to select from.

      Union Elbows offer by us to our clients are manufactured in many different sizes and dimensions to meet the specific requirement.


      Specifications:
      • Monel: Grade: Monel 400, Monel K500, Monel R-405
      • Nickel: Grade: Nickel 200, Nickel 201
      • Inconel: Grade: Inconel 600, Inconel 601, Inconel 625, Inconel 718
      • Incoloy: Grade: Incoloy 800, Inconel 800H, 800HT
      • Hastalloy: Grade: Hastalloy B2, Hastalloy B3, Hastalloy C22, Hastalloy C276, Hastalloy X
      • Titanium: Grade: Gr1, Gr2, Gr3, Gr5, Gr7, Gr11
      • Stainless Steel: Grade: ASME / ASTM SA / A403 SA / A 774 WP-S, WP-W, WP-WX, 304, 304L, 316, 316L, 304/304L, 304H, 316H, 316/316L, 321, 330, 347, 309/S, 310/S, 317/L, 333, 410/S, DIN 1.4301, DIN1.4306, DIN 1.4401, DIN 1.4404
      • Carbon Steel: Grade: ASTM A 234 WPB , WPBW, WPHY 42, WPHY 46, WPHY 52, WPH 60, WPHY 65 & WPHY 70
      • Duplex Steel: Grade: ASTM / ASME A/SA 182 UNS F44, F45, F51, F53, F55, F60, F61
      • 1/4" , 1/2" & 3/4"  Custom size available as per requirement
      • NPT, BSPT, BSP & Socket Weld.


      Additional Information:

      • Delivery Time: Ready Stock
      Get Best QuoteRequest A Callback
      Stainless Steel Union Cross

      Stainless Steel Union Cross

      Product Price: Rs 100 / PieceGet Best Price

      Product Details:
      Usage/ApplicationChemical Handling Pipe
      Size1/4"
      MaterialSS
      Pressure6000 psi (413 bar)
      BrandMPJ
      ConnectionNPT
      Country of OriginMade in India

      We manufacture, supply and export Union Fittings which are very useful in various types of connecting functions in the big industries. Our union fittings are of four types to be used in many different works in the varied industries.

      Our in-house production of Union Cross is manufactured with excellent quality of raw materials to suit the fixing work mainly in electrical industries, air conditioning industries. These products of ours have been well demanded and extensively used by the clients of diverse category in different size. These Cross have part numbers of numerous kinds to select from.




      Additional Information:

      • Delivery Time: Ready Stock
      Get Best QuoteRequest A Callback
      Reducing Union

      Reducing Union

      Product Price: Rs 150 / PieceGet Best Price

      Product Details:
      MaterialSS
      Usage/ApplicationGas Pipe
      End Connection TypeSocketweld
      BrandMPJ
      ApplicationGas Pipe
      Size3/4"
      Country of OriginMade in India

      We manufacture, supply and export Reducing Union Fittings which are very useful in various types of connecting functions in the big industries. Our Reducing Union fittings are of four types to be used in many different works in the varied industries.

      Our in-house production of Reducing Union is manufactured with excellent quality of raw materials to suit the fixing work mainly in electrical industries, air conditioning industries. These products of ours have been well demanded and extensively used by the clients of diverse category in different size. These Cross have part numbers of numerous kinds to select from.



      Additional Information:

      • Delivery Time: Ready Stock
      Get Best QuoteRequest A Callback
      Union Tee

      Union Tee

      Product Price: Rs 80 / PieceGet Best Price

      Product Details:
      MaterialSS
      End Connection TypeSocketweld
      Usage/ApplicationHydraulic Pipe
      Size3/4"
      Working Pressure6000 psi (413 bar)
      BrandMPJ
      Country of OriginMade in India

      We manufacture, supply and export Union Fittings which are very useful in various types of connecting functions in the big industries. Our union fittings are of four types to be used in many different works in the varied industries.

      Our in-house production of Union Tee is manufactured with excellent quality of raw materials to suit the fixing work mainly in electrical industries, air conditioning industries. These products of ours have been well demanded and extensively used by the clients of diverse category in different size. These Tee have part numbers of numerous kinds to select from.

      The raw material used for the fabrication of this union is checked on various parameters in order to ensure its flawlessness. Widely caters the needs of various industries like food processing, paper, sugar, petroleum refineries, cement, beverages and dairy plants, clients can avail this assortment from us in standard as well as customized options as per their varied specifications.



      Additional Information:

      • Delivery Time: Ready Stock
      Get Best QuoteRequest A Callback
      Copper Cap

      Copper Cap

      Product Price: Rs 10 / Piece(s)Get Best Price

      Product Details:
      Size2 inch
      Usage/ApplicationPipe Fitting
      ShapeRound
      Thickness3 mm
      Country of OriginMade in India
      MaterialCopper
      TechnicsHydraulic press
      BrandM P Jain
      M P Jain Tubing Solutions LLP was found in 1972 in order to satisfy the growing requirements of our specialist piping products on quick deliveries to the Oil & Gas, Petrochemical, Nuclear, Liquefied Natural Gas (LNG) Industries, Power Plants. We had established a global foothold in 1980. 
      Get Best QuoteRequest A Callback
      Stainless Steel Hex Nipples

      Stainless Steel Hex Nipples

      Product Price: Rs 50 / PieceGet Best Price

      Product Details:
      Thread Length20 mm
      End Connection TypeThreaded
      MaterialSS
      Thickness25 mm
      Surface FinishVarnished
      BrandM P Jain
      Size3/4 inch
      Country of OriginMade in India
      We are offering Stainless Steel Hex Nipples to our client.
      Get Best QuoteRequest A Callback
      Steel Oltes

      Steel Oltes

      Product Price: Rs 200 / PieceGet Best Price

      Product Details:
      ClassClasses 150
      Usage/ApplicationChemical Fertilizer Pipe
      MaterialSS
      BrandM P Jain
      GradeSS316
      Thickness9 mm
      Surface TreatmentPolished
      M P JAIN Are Manufacturers Of Steel Olets. We are one of the top Manufacturers of ASME B16.11 Steel Sockolets in India. We accomplish a Lot of admiration by our customers owing to its dimensional accuracy, high tension thikness, corrosion resistantancy and Quality products.

      We manufacture according to proven designs and from the highest quality materials; the outlet components we Supply are Suitable for a variety of Heavy Duty Applications.
      • Steel Weldolets,
      • Steel Threadolets,
      • Steel Sockolets,
      • Steel Elbolets,
      • Steel Latrolets,
      • Steel Nippolets,
      • Stainless Steel thermowell,
      • Steel Coupolets,
      • Steel Brazolets,
      • Steel Sweepolets

      Classes 150 LBS to 9000 LBS:


      Material

      Stainless Steel ASTM A 403, Grade WPS/WPW 304, 304L, 304H, 316, 316L, 316Ti, 310, 310S, 321, 321H, 317, 347, 347H

      Duplex & Super Duplex Steel S32750, S32760, S31803, S31805, S32340, S32205

       

      Carbon Steel ASTM A 234, Gr. WPB/WPBW, (IBR/Non IBR)
      Alloy Steel ASTM A 234, Gr. WP1, WP11, WP22, WP5, WP9, WP91, (IBR/Non IBR)

       

      Nickel Alloys Monel 400 & 500, Inconel 600, 625, 800, 825, Hastelloy C-276, C-22, B2 etc

       

      Titanium Grade 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12

       

      Copper Alloys Cu-Ni 70-30, Cu-Ni 90/10 etc

       

      Special Metal 253MA, 254SMo, 904L

       



      Additional Information:

      • Pay Mode Terms: T/T (Bank Transfer)
      • Port of Dispatch: JNPT
      • Delivery Time: READY STOCK
      Get Best QuoteRequest A Callback
      Copper Fastener

      Copper Fastener

      Product Price: Rs 550 / Kilogram(s)Get Best Price

      Product Details:
      BrandM P Jain
      Packaging TypePlastic Bag
      MaterialCopper
      Country of OriginMade in India
      Thickness4.50 mm
      TechniqueHot Rolled
      Head ShapeHexagonal
      We are offering Copper Fastener to our client.

      Thickness Range:
      • 4.50-40 mm
      Get Best QuoteRequest A Callback

      EXPLORE MORE CATEGORIES

      Contact Us
       
      Thank youYour Enquiry has been sent successfully.
      © M P Jain Tubing Solutions LLP. All Rights Reserved (Terms of Use)Developed and managed by IndiaMART InterMESH Ltd.